Gray Posted October 31, 2011 Report Share Posted October 31, 2011 Just cut a new key for my car, TPX2 chip 3 button key. Can someone give me the sequence to programme the key. I havn't done one before and I thought I'd have a go on my own motor first. Thanks Link to comment Share on other sites More sharing options...
Gray Posted October 31, 2011 Author Report Share Posted October 31, 2011 It's OK I think I just found the answer here. I think .............viewtopic.php?f=3&t=5726&p=55100&hilit=ford+3+button#p55100 Link to comment Share on other sites More sharing options...
completelocks Posted October 31, 2011 Report Share Posted October 31, 2011 to program the key or the remote? If you have a TPX2 in it, you aint gonna program that to start the car, that's to clone the original transponder onto. If you have a cloner then no programming of key is needed. You'll need an internet connection though. Programming a new key into the car is done with an MVP Pro or similar. Remote is ignition on and off 4 times, wait for chime, then press button Link to comment Share on other sites More sharing options...
Gray Posted October 31, 2011 Author Report Share Posted October 31, 2011 Done the chip on the keycrypt matey. Just need to do the 3 button remote. Link to comment Share on other sites More sharing options...
Lee Posted October 31, 2011 Report Share Posted October 31, 2011 Remote is ignition on and off 4 times, wait for chime, then press button on all remotes, other wise your new one will work & the original won't Link to comment Share on other sites More sharing options...
completelocks Posted October 31, 2011 Report Share Posted October 31, 2011 good point, I forgot to mention that bit Link to comment Share on other sites More sharing options...
Gray Posted October 31, 2011 Author Report Share Posted October 31, 2011 Triffic..... good job I ain't tried it yet...........That there "thekeyvan's" a top bloke, lots of PM advice..not that I am saying I have not taken your advice on board too chaps...thanks.......... Link to comment Share on other sites More sharing options...
Gray Posted November 7, 2011 Author Report Share Posted November 7, 2011 Followed instructions to the letter now my original remote don't work Link to comment Share on other sites More sharing options...
grahamparker Posted November 7, 2011 Report Share Posted November 7, 2011 Did the car beep after the 4th turn and again when you pressed a button on each remote ? Link to comment Share on other sites More sharing options...
Gray Posted November 7, 2011 Author Report Share Posted November 7, 2011 Yep I'll have another go tonight. Link to comment Share on other sites More sharing options...
grahamparker Posted November 7, 2011 Report Share Posted November 7, 2011 Did you turn the ignition back to position 2 then off after pressing a button on the remotes. You need to do this to end the programming sequence. Ignition on(position 2) to off 4 times.Car beeps Press a button on remotre,car beeps once for each remote. Turn ignition to position 2 then off.Wait 1 minute then try. Give that a go gray that should do the trick. Link to comment Share on other sites More sharing options...
Gray Posted November 7, 2011 Author Report Share Posted November 7, 2011 Ah Ha that could be it. I never waited a minute. I got a bit over enthusiastic...Came too quick Link to comment Share on other sites More sharing options...
StevenB Posted November 7, 2011 Report Share Posted November 7, 2011 I got a bit over enthusiastic...Came too quick And at your age too - well done Link to comment Share on other sites More sharing options...
Gray Posted November 7, 2011 Author Report Share Posted November 7, 2011 I ain't done yet..Still life in the old dog... Link to comment Share on other sites More sharing options...
rapidlocks Posted November 8, 2011 Report Share Posted November 8, 2011 also to be clear as i know many who have asked the same question , and in their case they hadnt pressed the button on the existing remote so it got programmed out . so turn ignition on/off 4 times , the dash should sound press any button on the 1st remote , dash should sound again then press any button on the 2nd remote ( and any further remotes in turn ), dash should sound again turn ignition on of again all remotes should be programmed. Link to comment Share on other sites More sharing options...
Count Muppet Posted November 8, 2011 Report Share Posted November 8, 2011 When I did mine, I had to press the lock button for it to work. Link to comment Share on other sites More sharing options...
grahamparker Posted November 8, 2011 Report Share Posted November 8, 2011 You done yours yet Gray ??? Link to comment Share on other sites More sharing options...
Craig Gardner Posted November 8, 2011 Report Share Posted November 8, 2011 You done yours yet Gray ??? i beleive its on his daughters focus now. craig Link to comment Share on other sites More sharing options...
Gray Posted November 9, 2011 Author Report Share Posted November 9, 2011 Mine and my daughters keys are now sorted, all working. Thanks guys. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now