Tibbe Key Identification

[Deni P.]

Can someone decode this key

[David C]

Which cut are you not sure about?

[EST]

[Deni P.]

13 minutes ago, EST said:

So code is 213314?

[Deni P.]

2 hours ago, Deni P. said:

This one @David C

[grahamparker]

6 hours ago, Deni P. said:

So code is 213314?

YES.

[Deni P.]

Thanks so much!

[Deneteus]

Can you decode the following Ford tibbe key. I think its 214114 but I want to make sure all those 4's aren't 3s. 
I looked at some reference photos. 

https://photos.app.goo.gl/wJ2PMTk9Vrf7wFnc8

 

 

[David C]

Yes, the 4s are definitely 4s.

[Deneteus]

1 minute ago, David C said:

Yes, the 4s are definitely 4s.

You Rock!

[Auto Key Wizard]

Cuts are 314224

[Deneteus]

On 5/23/2024 at 5:55 PM, Auto Key Wizard said:

Cuts are 314224

Did you look at the album? That first cuts not very deep. 

 

[Auto Key Wizard]

First cut is 3 depth

Cut 314224 it will work

[Deneteus]

1 hour ago, Auto Key Wizard said:

First cut is 3 depth

Cut 314224 it will work

I'll let you know how it goes!

[Growster]

5 hours ago, Auto Key Wizard said:

First cut is 3 depth

Cut 314224 it will work

This was probably not the most difficult decode, OK, but it makes this nonetheless a good moment to say that I am impressed by your decoding abilities.

[Deneteus]

On 5/23/2024 at 7:32 PM, Auto Key Wizard said:

First cut is 3 depth

Cut 314224 it will work

Update!! So we started to cut them this morning early realized that the 2nd cut was a 2.

We referenced the original key versus a blank with an XHORSE which caught the error.

It took me literally all day to program though because of some bad instructions on my Autel MX808, but everything works as expected!
 

[Count Muppet]

Must be a worn lock because I’m 95% certain it should be a 1

[grahamparker]

17 hours ago, Deneteus said:

Update!! So we started to cut them this morning early realized that the 2nd cut was a 2.

We referenced the original key versus a blank with an XHORSE which caught the error.

It took me literally all day to program though because of some bad instructions on my Autel MX808, but everything works as expected!
 

A keen eye is required to decode these, I agree with Terry that the cuts shown are as he stated. Look at the distance from edge of cut down to the main body. Seems quite clear the distance is greater than 2’s.

[grahamparker]

[Torment]

Can someone confirm the key code please

[Michael]

43 minutes ago, Torment said:

Can someone confirm the key code please

332434

[Torment]

Thanks but are you sure the first cut from left 3 ?

[grahamparker]

6 minutes ago, Torment said:

Thanks but are you sure the first cut from left 3 ?

Yes but not been cut very well. Although they look different they are both 3.

[Torment]

Ok, thanks 

[Torment]

Can someone clarify the process of supplying a red tab Ford Tibbe key with transponder incorporated within the key.

I was of the belief that the transponder chip within the new key is blank/uncoded and via the use of Master Key and the programming sequence, a new code is programmed into the new keys transponder chip (apparently up to 15 Keys can be programmed)

I’ve been of the belief that a new key can only be programmed via the Red Master Key but I’m been told this is obsolete now and the Master key is not needed ?