simong Posted February 8, 2013 Report Share Posted February 8, 2013 Anybody had problems with TP00HUHAAP1 in the uk our last ones were all faulty could not do tpx4 jma ,noware to put the chip, jma france have now said it is off the market and send back any feedback would be good regards simon Link to comment Share on other sites More sharing options...
derek Posted February 8, 2013 Report Share Posted February 8, 2013 was the problem the cavity where the tpx chip sits too shallow or something else? a little more detail may help in some replies to you Link to comment Share on other sites More sharing options...
simong Posted February 8, 2013 Author Report Share Posted February 8, 2013 was to shallow Link to comment Share on other sites More sharing options...
derek Posted February 8, 2013 Report Share Posted February 8, 2013 Did you try cutting the red plastic piece diwn so it would fit? Link to comment Share on other sites More sharing options...
keyfast Posted February 9, 2013 Report Share Posted February 9, 2013 Derek, read the post ?? Link to comment Share on other sites More sharing options...
derek Posted February 9, 2013 Report Share Posted February 9, 2013 Derek, read the post ?? i did, but by asking a simple question it was apparent there was "somewhere" to put the chip, just that the somewhere wasn't big enough, not that there was "nowhere", as i have had this problem and the tpx chip fitted in and all i needed to do was cut down the red plastic holder so only the top of it was used as a stopper, so maybe you could try reading the post Link to comment Share on other sites More sharing options...
grahamparker Posted February 9, 2013 Report Share Posted February 9, 2013 Derek is right as i have done the same with some silca blanks. Also managed to drill a hole to take a chip when i didn't have the right blank once.Didn't look to bad when the tpx 2 was inserted and a little blob of glus on top to seal it in. Some of the Landrover (NE38) cases need to be drilled otherwise the car doesn't see the chip when replacing a snapped key. Link to comment Share on other sites More sharing options...
simong Posted February 9, 2013 Author Report Share Posted February 9, 2013 thanks for the advice had four to do, took me 3 hours to drill the plastic to fit the tpx4,s plus a bit a super glue all working got a landrover tomorrow will get up early to drill it out ,thanks graham ps used to live in legsby avenue Link to comment Share on other sites More sharing options...
grahamparker Posted February 9, 2013 Report Share Posted February 9, 2013 thanks for the advice had four to do, took me 3 hours to drill the plastic to fit the tpx4,s plus a bit a super glue all working got a landrover tomorrow will get up early to drill it out ,thanks graham ps used to live in legsby avenue Where do you live now. ?? Link to comment Share on other sites More sharing options...
simong Posted February 9, 2013 Author Report Share Posted February 9, 2013 brittany france married a french girl after moving around the uk Link to comment Share on other sites More sharing options...
grahamparker Posted February 10, 2013 Report Share Posted February 10, 2013 A little different to GRIMsby then. Link to comment Share on other sites More sharing options...
ponsaloti Posted February 10, 2013 Report Share Posted February 10, 2013 thanks for the advice had four to do, took me 3 hours to drill the plastic to fit the tpx4,s plus a bit a super glue all working got a landrover tomorrow will get up early to drill it out ,thanks graham ps used to live in legsby avenue Bloody hell, were you using a matchstick and a bit of string to drill the hole ? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now