Jump to content
lock&quay

Best electronic Machine for Yale Superior & Dimple keys .

Recommended Posts

2 hours ago, grahamparker said:

Triax e-Code expensive but well worth the investment if you can afford it.

Yes it does need a lot of cutters and jaws but i could not live without mine now.

I just had laugh at the price lol .... I can't justify that type of budget as I'm not Vat registered .

Share this post


Link to post
Share on other sites
3 hours ago, grahamparker said:

Mine has cut over 12,000 keys now and still works the same as the day we bought it you do get what you pay for.

Occasionally a second hand one appears but they aren't always in the best condition, i look after my machines.

I have no doubt that it is a good machine , I have some high end Borkey machines I might let go as I hardly use them to justify a purchase & make room . 

Share this post


Link to post
Share on other sites

Best machine is the triax e code but on you could look at the miracle A9. Used one in the smaller branch for your & not had a problem. Much slower than a triax e code & the finish on the key is not the same level but for smaller volumes of keys it does the job fine. 

Share this post


Link to post
Share on other sites

Not the Futura anyway!

I wonder if someone could compare these and suggest a cutting code please?  Original customer key is the first then and then what the Futura decided it should be.

2018-07-14 10.11.54.jpg2018-07-14 10.14.08.jpg

Share this post


Link to post
Share on other sites

We don’t do those Yale on the Futura we do them manually, but one thing have learnt with the futura the customer key has to be clean ie no dirt or crap  on the key. Look at the customers key and see all the black dirt and grim that affects the decoding. 

What we do is with all keys going into the Futura is to use a wire brush to clean the crap from the cuts and it will deccode correctly. 

Hope it helps 

Edited by eimco
Spelling mistakes

Share this post


Link to post
Share on other sites

The key you have pictured Simes the cuts are

A13221

B1312

C2121

Cutting card on my triax is the magnum card 3218 not sure if it is the same for the futura.

I have also set my Z Axis cut at -10 in the Silca SKP software as they where sometimes a little tight in turning in the cylinder not sure again if you have that freedom with the Futura.

Share this post


Link to post
Share on other sites
24 minutes ago, eimco said:

We don’t do those Yale on the Futura we do them manually, but one thing have learnt with the futura the customer key has to be clean ie no dirt or crap  on the key. Look at the customers key and see all the black dirt and grim that affects the decoding. 

What we do is with all keys going into the Futura is to use a wire brush to clean the crap from the cuts and it will deccode correctly. 

Hope it helps 

Thanks mate :)

Share this post


Link to post
Share on other sites

we have a Futura pro, but, its too slow (funny rhymes) so we always manually cut them on the Silca matrix evo. ten times better and never fails... So good that i would sell the Futura which has cut a hand full of keys...

Share this post


Link to post
Share on other sites
18 hours ago, B.C said:

we have a Futura pro, but, its too slow (funny rhymes) so we always manually cut them on the Silca matrix evo. ten times better and never fails... So good that i would sell the Futura which has cut a hand full of keys...

I don't understand the hurry! Allow the customer to watch there key being cut, they appreciate the extra cost a lot more.

You don't actually stand there watching it yourself do you?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×